Voron 0 Display Installation, Configuration and Features

In this video, I walk through the install, assembly, and Klipper configuration for the Voron 0 Display. My goal with this video is to provide all the steps in a relatively concise format from start to finish. This is a pretty straightforward upgrade, and I'd guesstimate you could do it in about an hour (or even less) once you have the parts printed. Cutting and crimping a USB cable adds time, but I think it's worth the effort and will give you the cleanest install. Correction: The self tapping screws needed are 12mm, not 8mm. I didn't end up using them, and they are hard to source- so I'd say don't bother with them. Special thanks to Steve Builds as well- I watched his Live Stream and took away a few ideas (like the JST-XH). I encourage you to check his video out for additional info. https://www.youtube.com/watch?v=JJlL1S-_v0I Scroll down to jump to specific areas: 0:36 - Walkthrough of Display Screen Features 2:48 - Parts Required 4:21 - Note about Heat Inserts 7:03 - Using a JST-XH for a clean install 7:50 - Installing heat Inserts 9:00 - Assembly of Screen into 3d Printed Parts 10:03 - Cutting a USB cable and crimping JST-XH connectors 15:06 - Powering up 15:12 - Getting device DFU ID 15:55 - Compiling Klipper 16:56 - Flashing Klipper to Voron 0 Display 17:20 - Confirming Klipper flashed 17:33 - Downloading DisplayEncoder.cfg from Github, and Uploading to Mainsail 18:17 - Adding an include line in Printer.cfg for DisplayEncoder.cfg 18:47 - Finishing up the install 19:57 - Summary and Conclusion Main link to Voron 0 Display Github. You can find the STL's, Assembly Information, config file, etc. all from the Github. Scroll down for specific links as well. https://github.com/VoronDesign/Voron-Hardware/tree/master/V0_Display Direct Link to Klipper Install and Flashing Guide: https://github.com/VoronDesign/Voron-Hardware/blob/master/V0_Display/Documentation/Setup_and_Flashing_Guide.md Direct Link to STL's. I printed the knob, housing front, housing rear, (no usb option) and the single piece mount in the v0.1 folder. https://github.com/VoronDesign/Voron-Hardware/tree/master/V0_Display/STLs Direct link to DisplayEncoder.cfg: https://github.com/VoronDesign/Voron-Hardware/blob/master/V0_Display/Software/DisplayEncoder.cfg Where to buy? Because of the chip shortage, it may be hard to find/source a display. Here are a few links to check. I purchased mine here: https://www.fabreeko.com/products/ldo-voron-v0-display DeepFriedHero: https://deepfriedhero.in/products/voron-v0-display Aliexpress: https://www.aliexpress.com/w/wholesale-voron-v0-display.html Printed Solid: https://www.printedsolid.com/products/ldo-voron-v0-display?variant=39319639162965 Example kit for the JST XH connectors needed: https://www.aliexpress.com/item/4000126563819.html?spm=a2g0o.productlist.0.0.2add42caFjOO8u&algo_pvid=71fdcea7-ff1d-4bb2-9f47-50d8aa4f801c&algo_exp_id=71fdcea7-ff1d-4bb2-9f47-50d8aa4f801c-0&pdp_ext_f=%7B%22sku_id%22%3A%2210000000365693778%22%7D&pdp_pi=-1%3B0.69%3B-1%3BUSD+1.52%40salePrice%3BUSD%3Bsearch-mainSearch Tools featured in my video are linked below. These are Amazon Affiliate Links. If you are considering buying a tool, please use my link- it costs you nothing extra, and helps me out. As an Amazon Associate I earn from qualifying purchases. Thanks for your support! Engineer PA-09 Crimpers - https://amzn.to/3aLgZB9 Hakko 888FX High Quality Soldering Iron - https://amzn.to/3FZtsiM Heat Insert Tips - https://amzn.to/3aLh6N5 Capri Wire Strippers - https://amzn.to/3ctPY62 Quick Reddit Post that is helpful on customizing the display menus:: https://www.reddit.com/r/klippers/comments/pbxloi/changing_lcd_menu_layout_in_klipper/